Response Electronics CL6011B Spécifications télécharger pdf (Page 26)

2-10 Using the Calibrator

UM4.6:CS6003 Original — December 1991

Range — 0 to 20 mA

Accuracy — ± 0.05%

Decade Resistance Box (used for calibration of Type DM6331 RTD

Input Unit)

Range — 0 to 200 ohms

Accuracy — ± 0.005 ohms

Resolution — ± 0.01 ohms

Pulse Generator or Waveform Generator (used for calibration of Type

DM6371 and DM6372 Pulse Count Input Units)

Range — 0 Hz to 10 KHz

Resolution — 1 Hz or better at low end and 100 Hz at top end

Accuracy — ± 2%

Amplitude — 0 to 10 Vp-p

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 169 170

Using and Maintaining the 1
Type CS6003 Calibrator 1
Documentation Map 3
Appendixes 8
Contents 10
Original — December 1991 10
UM4.6:CS6003 10
Section Tab Guide 11
1 Introduction 13
1.5 Related Documents 14
1.6 Manual Conventions 15
1-4 Introduction 16
2 Using the Calibrator 17
2.2.1 Cables 18
2.2.2 Front Panel 18
Using the Calibrator 19
2.2.2.7 Breakout Terminals 20
2.2.2.11 Numerical Display 20
2.2.2.12 Family Switches 21
2.2.2.13 Group Mode Switches 21
2.2.2.14 CHK MOM Switch 21
2.2.2.15 CARD IDENT Switch 21
2.2.2.16 Mode Switches 21
2.2.2.17 Status Indicator 22
2.2.2.18 Data Switches 22
2.3 Operating the Calibrator 23
2.3.4.1 Lamp Test 24
2.3.4.2 Procedures 24
± 0.1% ± 1 count 25
± 0.002 Vdc 25
± 0.0005 mV 25
± 0.005 ohms 26
± 0.01 ohms 26
3 Card Removal, Cleaning, and 27
Installation 27
3.3 Circuit Card Cleaning 28
3.4 Corrosion 29
4 Input and Output Card 31
4.1.1.2 Equipment Required 32
4.1.1.3 Calibration Procedure 32
Input and Output Card 33
(Isolated) 34
X00606–A 35
4.1.3.1 Overview 39
4-10 Input and Output Card 40
Figure 4-3. RTD Input Card 40
R2, and R3 for the RTD card 40
4.1.3.2 Equipment Required 41
4.1.3.3 Calibration Procedure 41
1. Zero adjustment 43
2. Span adjustment 43
4.1.4.1 Overview 44
4-15Input and Output Cards 45
4.1.4.2 Equipment Required 46
4.1.4.3 Calibration Procedure 46
Input Cards 48
4.1.5.1 Overview 49
4.1.5.2 Equipment Required 49
4.1.5.3 Calibration Procedure 50
4.1.6.1 Overview 50
4.1.6.2 Equipment Required 51
4.1.7.1 Overview 54
4.1.7.2 Equipment Required 54
4.1.7.3 Calibration Procedure 54
Input and Output Cards 56
X00613–A 57
4.1.8.2 Overview 60
4.1.8.3 Equipment Required 60
4.1.8.4 Calibration Procedure 60
Current Output Cards 61
4.2.1.2 Equipment Required 62
4.2.1.3 Calibration Procedure 62
1. 0=OFF; 1=ON 64
X00616–A 65
REMOVE W1 FOR 65
MOMENTARY OPTION 65
4.2.3.2 External Relay Panel 74
4.2.3.3 Switch Settings 74
4.2.3.4 Overview 74
4.2.3.5 Equipment Required 74
4.2.3.6 Calibration Procedure 75
4-48 Input and Output Cards 78
5 Controller Cards 79
5.1.1 MPU Card 80
5.1.2 Process I/O Card 83
5.2.1 MPU Card 85
5.2.1.2 Calibration Procedure 86
5.2.2 Process I/O Card 88
5.2.2.2 Calibration Procedure 89
5.3.1 Equipment Required 92
5.3.2 Calibration Procedure 92
5.4.1 Equipment Required 94
5.4.2 Calibration Procedure 95
5.5.1 Equipment Required 97
5.5.2 Calibration Procedure 97
(with Dual Current Output) 99
5.6.2 Calibration Procedure 100
± 0.01 volts dc 101
± 0.02 volts dc. If not, the 101
Manual Control Cards 102
5.7.2 Calibration Procedure 103
5.8.1 Equipment Required 104
Conversion Card 105
5.9.2 Calibration Procedure 106
Controller Cards 107
± 0.015 volts dc. If 108
5.10.1 Equipment Required 110
5.10.2 Calibration Procedure 110
5.10.3 Functional Test 111
± 0.08 volts 112
5.11.1 Equipment Required 114
5.11.2 Calibration Procedure 114
6 Data Highway Cards 115
6.1.2 Calibration Procedure 116
± 0.050 volts 117
± 0.002 volts dc 117
± 0.005 volts dc. If not 117
Devices)(PN41B0985) 118
6.2.2 Calibration Procedure 119
± 0.010 volts 120
± 0.050 volts dc on the 120
Appendix A 121
Maintaining the Calibrator 121
A.3 Lamp Test 122
A.4 Fan and Filter 122
Glossary 123
DM6461, DM6462, DM6463, Using 159
Document by Number 159
UM4.6:CS6003, 1-1 159
Reader’s Evaluation 167
1712 CENTRE CREEK DR 168
AUSTIN TX 78754–9971 168

Commentaires sur ces manuels

Pas de commentaire

Response Electronics CL6011B Spécifications Page 26

Commentaires sur ces manuels